picked up a 64 falcon futura - Ford Muscle Forums : Ford Muscle Cars Tech Forum

fordrule · 02-14-2013, 11:02 AM

The car is a 64 futura 2 door V8 car that was a 260 4 spd. it doesn't have any drive train so I am starting new

these are picks the previous owner took at his house

how she sits right now just under a cover under his porch

Checked the VIN code
4 Year 1964

H Assembly Lorain, OH

17 Body Falcon Futura 2-Door Hardtop

F Engine 8 Cyl. 260 CID

fordrule · 02-14-2013, 11:03 AM

I have a 95 302 that had 60k miles on it but has been sitting for a couple of years...didnt look the best so a complete teardown is happening..

I couldn't resist with the pic

fordrule · 02-14-2013, 11:04 AM

got the motor all torn apart...now Im going to be calling the machine shop to see what its all going to cost...hot tank, hone and freeze plugs...

since its a 95 302 block the dipstick is in the block is there a block off for it? i picked up a set of valve covers and air cleaner from a 65 falcon and timing cover from a 79 302 so all I need now is a oil pan....will that air cleaner work with that carb if i use a spacer on the top of the carb...i was playing with it and saw that the carb linkage was hitting the bottom of the air cleaner...I am going for a stock appearance... debating on the 289 hipo k exhaust manifolds

fordrule · 02-14-2013, 11:05 AM

here is the pics I took when i went out to look at it. a little rust in the floors and a little in the trunk

fordrule · 02-14-2013, 11:06 AM

still need to pick up a transmission, radiator, rear bumper, different rear end and a bench seat...i'll be working on it this weekend and take some better pics

d_day · 02-14-2013, 01:50 PM

Looks like you've got your work cut out for you.

You know those are the wrong tail light lenses for a 64?

fordrule · 02-15-2013, 12:04 PM

yeah i was told that they are 65 tail lights...today i will be pulling the mustang out of the garage and the falcon in it to start digging into it

fordrule · 02-16-2013, 08:43 PM

some progress today

tomorrow is climbing into the engine bay and put her on jacks...hopefully pull fenders without all the bolts rusted to the nuts and maybe even pull, master cylinder, heater assy..

retyler · 02-17-2013, 09:59 AM

It's looking a lot better, keep at it you'll get there. A few of us have or are going through the same thing. Good luck to you.

desertfalcon · 02-17-2013, 10:31 AM

Cool project, always loved the 2 doors.

fordrule · 02-17-2013, 06:33 PM

got the hood and passenger fender off tonight...got the driver down except two bolts...one is rusted to the nut and the other one is the one in the cowl. and the nut plate let loose to im not sure how to get that one.. I have also been contemplating drilling out the bolt heads and just move on after the fender is off. My plan is to strip all the undercoating on the fender wells and strip the engine bay

fordrule · 02-21-2013, 08:03 PM

here is some more progress from the weekend. stripped the hood and both fenders and started to strip the undercoating and paint from the fenderwells. had to drill off two bolt heads. ones not going to be to hard to replace but the nutplate in the cowl is going to be a pain to replace. I am going to need to look at renting a media blaster and get it all done rather quickly

even my girlfriend was out there helping me.

this was an odd mod that I discovered...probably to adjust the clutch

fordrule · 02-21-2013, 08:04 PM

some of the bad of the floor

fordrule · 02-21-2013, 08:25 PM

fordrule · 03-08-2013, 08:31 PM

here is some progress today...hopefully finish up the core support and prep ir for paint. I need to take some pics of the rust damage so i can get some advice on how to attack it....