pride63

Today I wired a new switch into my air ride system so I can control with a palm held unit , Also my mate cut this rot out of my front passenger footwell.

front footwell rust by mark & anne's photos, on Flickr

photo by mark & anne's photos, on Flickr
He then fabricated some replacement panels and welded them in


photo by mark & anne's photos, on Flickr

photo by mark & anne's photos, on Flickr
Hopefully if the weather hold outs tomorrow we will do the other side.



What have you done today?

lagalaxie500

FLINTSTONES!!.come to mind.good luck.

RAGGAREN

got a haircut.....dont know if that counts..but i needed it....

floor looks good tho.....

__________________
Lars...
64 galaxie 500 2dr fastback... 390 4v, 4spd close ratio toploader, 4.11 rear..far from perfect but getting there...

JD66Falcon

Not a dang thing! Going for the haircut also that is next to a hobby store. I think its time to start building models again! This winter and being disabled is killing me!

__________________
2003 Bonneville SLE Some Mods
1968 Galaxie Country Sedan Wagon 390/Auto all original

EXracer4speed

So far got rid of the snow on the drive way and just woke up from a nap.

__________________
64 Galaxie XL - soon to be 427/toploader

ShotRod64

Sat at home waiting on another no-show for the Escort. Had other things i'd preferred to do like go to the swap meet at the corvette show. Don't care bout the cars but like to look at the swap goodies.

__________________


1964 Galaxie 500XL convertible, 390 .040 over, Fedmogul rv pro-3000 cam

Always be yourself, because the people that matter don't mind, and the ones who mind, don't matter.

http://www.so-calgalaxies.com
http://www.galaxiesnw.com

Sifu-Sitaigung

I got motivated to finish vacuuming out the rust particles out of the XL. I also got a sanding disk out and took the driver side seat foundation to bare metal and then primed it. I also took the air hammer out to cross-brace under the front of the rear seat to see how rotted it was where I could not see. Well, I will be pulling the brace out and replacing the entire pass. and driver side pans.. Front to back, including the rear seat pan. The bright side is - I will have a completely new , solid floor in the entire car when I am done. Still need to get my argon tank filled so I am not in a hurry..


Does that make any points for getting something accomplished? hehehe. I don't feel like it.

__________________
1967 Galaxie Fact. XL "Z" code (390-soon 445cid) C-6,A/C, P/S,P/B (K/H disc),Fact.Tinted glass
1967 Gal. Complete parts car
84 Grand Wagoneer, 94 Grand Cherokee Ltd.,2000 FLSTF,2012 FLHX

ShotRod64

Get yourself a gold star sticker. If you have a garage you can stick it to the door way or something each time you get something done. I got nothing done today so you did good.

__________________


1964 Galaxie 500XL convertible, 390 .040 over, Fedmogul rv pro-3000 cam

Always be yourself, because the people that matter don't mind, and the ones who mind, don't matter.

http://www.so-calgalaxies.com
http://www.galaxiesnw.com

Sifu-Sitaigung

If I did that I would end up doing more little projects here and there. WAIT! Then I might actually get something done! Great idea Shot Rod, lol hehehe Way to motivate me :-)

__________________
1967 Galaxie Fact. XL "Z" code (390-soon 445cid) C-6,A/C, P/S,P/B (K/H disc),Fact.Tinted glass
1967 Gal. Complete parts car
84 Grand Wagoneer, 94 Grand Cherokee Ltd.,2000 FLSTF,2012 FLHX

retyler

Nice job pride63, much more than I got done.

__________________
"Tell it like it is or don't tell it at all" 1964 Falcon 2dr HT, 347V8 4V, dual exhaust, 5sp, pwr assist R&P steering, AM radio, heater with defrost and 2sp fan, electric windshield wipers, cigar lighter, dlx light group, bucket seats, console and full carpet.

pride63

Today I stripped the crappy patch panel of drivers side front foot well and found more rust , suprie surprise . I seam sealed the repairs we did yesterday as well.
I trial fitted my rear bumper to work out where the LPG filler neck should sit behind number plate and then decided to fit in original fuel filler position next to original filler neck.
Now trying to decide on what colour to paint body next week. If only I could do photo shop lol

pride63

Today I stripped the 2 rear quarter windows and trim from inside and out ready for paint. Painted the new floor in rust oleum black gloss .


No one else working on their cars?????

puttster

Temperature here has fallen to 62 degrees. Only work I could do was take the clamp off the -battery terminal. Brrrrrr

__________________
When you're going through hell, keep going.
Putts drives a 1965 four door Galaxie. Rebuilt 390. 4100 on a Performer, AC, PS, PB w scarebird front discs, COM MX transm w/3.0 R.E. The seats, dash and hood are customized.

pride63

Lol, it was just above freezing today at work , good job my wagon is inside.

lagalaxie500

I got the bodyof the 63 Merc. unbolted from the frame in the shop today. Wheather permitting
tomorrow I'll pull it outside and use the Kubota to lift it off.