Complete new Duraspark setup 390 FE - Ford Muscle Forums : Ford Muscle Cars Tech Forum
 
LinkBack Thread Tools
post #1 of 2 (permalink) Old 06-20-2017, 05:15 AM Thread Starter
Registered User
 
Join Date: Apr 2013
Posts: 16
Complete new Duraspark setup 390 FE

I have a complete setup to convert over to a Duraspark ignition. I bought all of this to switch over my '64 Mercury. But I found out I actually have a FT engine block with the larger distributor bore and larger oil pump shaft, so this distributor won't fit my motor. My loss is your gain

Re-manufactured Motorcraft distributor. Some assembly oil on the shaft and gear, but its never been started on an engine. Distributor is for a '76 F-150 and has the dual vacuum advance.

New Motorcraft ignition module. This is the correct module with the blue strain relief grommet. I had it mounted on my fender but its never been used.

Brand new plug wire set. Never mounted

Brand new coil. OEM for a '76 F-150

New ballast resistor. This is the correct 1.3 Ohm resistor

Correct connectors for the distributor and coil. Two are still new in the package. One was installed on my harness so two of the wires have been cut short already. None of these have been used.

Everything you need to convert over from points to Duraspark. You will just need to wire up everything. Lots of how-to's on the net

$100 plus shipping
Attached Thumbnails
Click image for larger version

Name:	dis1.jpg
Views:	40
Size:	23.3 KB
ID:	137433   Click image for larger version

Name:	dis2.jpg
Views:	39
Size:	22.7 KB
ID:	137441   Click image for larger version

Name:	dis3.jpg
Views:	34
Size:	22.7 KB
ID:	137449  

Click image for larger version

Name:	dis4.jpg
Views:	39
Size:	22.8 KB
ID:	137457   Click image for larger version

Name:	dis5.jpg
Views:	30
Size:	22.2 KB
ID:	137465   Click image for larger version

Name:	dis6.jpg
Views:	39
Size:	21.2 KB
ID:	137473  

Click image for larger version

Name:	dis7.jpg
Views:	35
Size:	20.7 KB
ID:	137481   Click image for larger version

Name:	dis8.jpg
Views:	30
Size:	21.7 KB
ID:	137489   Click image for larger version

Name:	dis9.jpg
Views:	34
Size:	20.8 KB
ID:	137497  


1964 Mercury Marauder
Maynard is offline  
Sponsored Links
Advertisement
 
post #2 of 2 (permalink) Old 08-10-2017, 04:36 AM
Registered User
 
Join Date: May 2016
Location: Kingman Az.
Posts: 197
Re: Complete new Duraspark setup 390 FE

Before you sell all this, have you tried using the lower dist shaft on your FT dist in your new dist. Just takes a little disassembly and might save your project.
Lowrider is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Muscle Forums : Ford Muscle Cars Tech Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
Complete FE 3x2 Intake and Carbs 390 406 BH107 Air and Fuel 0 10-18-2012 02:10 PM
71-73 Mustang Brake Setup, complete retyler Brakes 0 08-11-2011 11:08 AM
Complete 65- (73?) Mustang drag race rear suspension setup, Calvert, Fab'd 9", etc jon volk Chassis and Suspension 0 06-28-2011 05:56 PM
PCV system setup for a 64 Galaxie 390 PaulG Galaxie Pages 24 04-04-2008 06:14 PM
How would a 3 x2 V or 2 x 4V carb setup work in a 390? ville All Ford Techboard 24 10-21-2005 05:04 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome