Ford Muscle Forums : Ford Muscle Cars Tech Forum - Reply to Topic
Thread: 393w build suggestion for valve springs Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now



In order to be able to post messages on the Ford Muscle Forums : Ford Muscle Cars Tech Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-16-2017 07:24 PM
fishbone1 My stash is growing
03-16-2017 01:25 PM
fishbone1 Yes, a rep from Eagle did respond. I appreciate that. Also, an employee at Clegg Engine in Utah has been very helpful with different rod weights. Since I am pretty sure my engine is going to be below 500fwhp I am going to use the Eagle 5.956 5140 rods and upgrade the 8740 bolts to ARP2000. Desktop Dyno pits my engine at 506hp/506trq. So, I will hope for 450/450.
03-15-2017 09:40 AM
GT350HR
Re: 393w build suggestion for valve springs

I think Ray from Eagle just emailed you on the weights.
03-14-2017 06:05 PM
fishbone1 I emailed eagle customer service. I really don't expect an answer.i contacted Lunati twice about valve springs with no reply. Maybe Eagle will surprise me.
03-14-2017 08:04 AM
GT350HR
Re: 393w build suggestion for valve springs


Contact Eagle or go to their website.
03-13-2017 12:14 PM
fishbone1 I just picked up a probe 4340 crankshaft that was internally balanced for a 1730 gram Bobweight. If my components go over the 1730 grams, can I have the crank externally balanced? How much can I go over and it won't cost me a fortune to rebalance. As I stand right now.
Pistons 464 grams
Pins 116 grams
Bearing. ???
Rod. Big end ????
Rod Small end. ????
I think I am pretty much limited to Eagle Sir5956p rods for 2 reasons. I have press pin pistons and the weight shouldn't throw me over in my Bobweight. Does anybody know the average big end and small end weight of the eagle 5.956 press fit rod? And the weight of a King bearing for 351?

Thanks
02-09-2017 02:16 PM
fishbone1 I have to wait a few weeks before I make any more purchases. I have exceeded my limit for Jan-Feb. Trying to keep it around $200 a month so the wife doesn't flip out. I have spent about $560 since 1 Jan. This adds up quickly. Probably be the end of the year before I complete all my parts purchases.
Heads $625 Dart Pro 1 195cc
Intake $225. Vic Jr
Piston.
Kit. $160. Mahle Forged 6.5cc
Rockers $225. Jim Miller
Cam. $175. Lunati
351w
Engine. $150. Craigslist
Lifters/
Spider. $140 m-6500-r302h
02-09-2017 10:35 AM
GT350HR
Re: 393w build suggestion for valve springs

That is the lifter I used on a '95 lightening block ( factory hydraulic roller to make it easy). Seat pressure doesn't kill them it's the over the nose load that does.
02-08-2017 09:33 PM
fishbone1
Re: 393w build suggestion for valve springs

Thanks for the Reply. I was thinking about the link bar lifters but I may go with the m-6500-r302h lifters instead. I can pick up those and the spider and dog bones for around $200. Or I can get Lunati Hydraulic roller link bars for around $350
02-08-2017 08:44 AM
GT350HR
Re: 393w build suggestion for valve springs

Hydraulic roller and OEM Ford Racing high rpm lifters. They have a ceramic check ball inside instead of the steel ball. I'm sure the spring has lost some pressure ( common) in the 25,000 miles the engine has seen. I initially ( mistakenly) used the GT40 springs that came on the heads out of the box. On the dyno the engine fell off at just under 6,000 rpm. They were between 92 and 100 from Ford. OK for a flat lifter hydraulic , nothing more. I had to put a chip in the Ford Racing ( MSD) box to limit the rpm to 7,000.
02-07-2017 10:43 AM
fishbone1 I thought I read somewhere that the max seat pressure on the Lunati and Howard's retrofit link bar lifters was 130. I could be wrong though. I am going to look for it.
02-07-2017 10:31 AM
fishbone1 Randy, Are you running a solid roller?
02-07-2017 10:17 AM
GT350HR
Re: 393w build suggestion for valve springs

I went with a spring from Competition Products that has 150 on the seat and about 380 open. 1.550 dia single spring and used a ti retainer. 7,000 rpm trouble free. I tossed the box years ago or I'd give you the part number.
Randy
02-07-2017 10:00 AM
fishbone1 I bought the cam used and can't find the part number on Lunati website. I sent a question to customer service a few days ago. I have received no reply.
02-07-2017 05:16 AM
Lowrider
Re: 393w build suggestion for valve springs

I would go to Lunati's web site and see what springs they recommend for that cam.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome