How much power will it make - Ford Muscle Forums : Ford Muscle Cars Tech Forum
 
LinkBack Thread Tools
post #1 of 2 (permalink) Old 09-06-2017, 06:41 PM Thread Starter
Registered User
 
Join Date: Mar 2017
Posts: 42
How much power will it make

I have a 1995 cobra block just a stock 5.0 roller block that's been prepped bored .30 over now is a 306 cid with je pistons for 13.0.1 compression 4340 forged rods with 7/16 rod bolts good for 1000 hp @ 8200 rpm I know I will not make that power but still over kill is better then not enough stock crank polished balanced cam is in the 250ish @ .50 duration 640ish lift intake and exhaust is 260ish @ .50 620ish lift on a 108 lsa and is a hydraulic roller cam with stock ford racing roller lifters AFR 220 renegade race heads that's been set up for my cam and the right spring pressures for my lifters a ported funnel web intake and 2 inch spacer toped with a Holley hp 750 carb running the stock in tank fuel pump with a regulator that will adjust from 180 psi all the way down to 5 psi with a return line will be turning around 7700 rpm bbk long tube headers that's 1 5/8 tubs in to a 3 inch collector will be upgrading soon just don't have an extra 1000 buck right now running a msd 8598 distributor with a HEI module set up no msd box here module was only 20.00 bucks and 4 wire hook up only running alternator and water pump with a g force upgraded t5 with a stage 3 clutch in a 3100 pound sn95 cobra I have been building this motor since October 2016 it is now September 2017 and next week I hope to start and brake it in. WHAT DO YOU THINK IT WILL MAKE AT THE FLY WHEEL AND AT BACK TIRE?????? thanks for your response hope you all enjoy your sbf cars and trucks
306afr220 is offline  
Sponsored Links
Advertisement
 
post #2 of 2 (permalink) Old 01-25-2018, 03:58 PM
Registered User
 
Join Date: Jul 2006
Posts: 644
Re: How much power will it make

Sounds like a hairy little mill, i;m assuming this is a strip only machine, i saw the 13-1 compression, that would be 110 octane required, eh?
cobra blocks any different than regular 5.0 blocks as far as strength?
From what i;ve read & witnessed once on a dyno, around 500 plus HP 5.0 factory blocks like to split right up the middle. (this one cracked along the cam journals, hardly noticeable till one run later)
Again, i don't know if the cobra 5.0 is beefier than the factory 5.0
HP- 410hp is my guess but, people with way more knowledge than i may chirp in here
royster is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Muscle Forums : Ford Muscle Cars Tech Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
How much power will it make 306afr220 Drag Racing 0 09-06-2017 06:39 PM
How much power will it make 306afr220 Dyno Board 1 09-06-2017 05:53 PM
make more power jkshavoc All Ford Techboard 12 04-08-2013 07:27 PM
How much power would it make? Hager All Ford Techboard 8 07-31-2008 02:57 PM
What is the best way to make more power with my engine? adgdghr123 All Ford Techboard 13 06-23-2004 04:38 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome